商品

EXFO MaxTester 735D OTDR for PON, FTTx & Metro Testing

Wavelengths

1310 / 1550 / 1625 nm

Dynamic range (typical)

42 dB

Event dead zone

0.7 m

Attenuation dead zone

3.5 m

EXFO PPM-350D PON Power Meter for Legacy & Next-Generation PON Activation

Model

EXFO PPM-350D

Product type

Handheld PON power meter

Supported technologies

GPON, EPON, XG-PON, XGS-PON, NG-PON2 and 10G-EPON

PON-aware function

Automatically detects the PON technology in use and adapts test parameters

Test modes

Optical power, loss and pass-through ONT/ONU verification

Fiber type

Singlemode

Fiber connector

SC/APC

Connectivity

Bluetooth and USB

Auto-wavelength switching

Yes

Reporting

Compatible mobile application workflow for storing results and creating reports

光纖衰減器

Manufacturer

FTTMAX

Selected configuration

FX-OFAT-FV-SC; SC-flanged variable attenuator

Attenuation range

0-30 dB, variable

Fiber type

Singlemode

Operating wavelength range

1260-1650 nm

Connector configuration

SC flange

藤倉 100S+ 光纖熔接機

Alignment

Active core alignment; single-fiber splicing

Fiber compatibility

Single-mode and multimode optical fiber

Average splice time

SM FAST: 7-9 s; SM AUTO: 11-13 s; AUTO: 14-16 s

Average heating time

60 mm SLIM mode: 8-10 s; 60 mm mode: 13-15 s

Average splice loss

ITU-T G.652 and G.657: 0.02 dB; G.651: 0.01 dB; G.653, G.654 and G.655: 0.04 dB

Battery endurance

Approximately 300 splice-and-heat cycles under the manufacturer test conditions

Measurement conditions

Times are measured at room temperature; heating uses the AC adapter. Loss is measured by cut-back after joining the same fiber type. Results vary with environment, fiber and sleeve; heating also depends on battery condition. Battery testing uses a new battery, power-saving settings and one splice-and-heat cycle per minute at room temperature.

Fujikura 88S 光纖熔接機

Alignment method

Active core alignment

Splice time (typical)

7 s

Heat time (typical)

14 s

Typical splice loss (SMF)

0.02 dB

Applicable fibers

SMF / MMF / DSF / NZDSF

藤倉 90R 帶狀光纖熔接機

Alignment method

Fixed V-groove (ribbon)

Fiber count

Single to 12-fiber ribbon

Splice time (typical, 12f)

17 s

Heat time (typical)

30 s

Typical splice loss (SMF)

0.05 dB

藤倉 90S+ 熔接機

Alignment method

Active core alignment

Splice time (typical)

7 s

Heat time (typical)

14 s

Typical splice loss (SMF)

0.02 dB

Applicable fibers

SMF / MMF / DSF / NZDSF

Battery capacity

Up to 400 splice + heat cycles

Fujikura ADC-20 AC Adapter for Select 90-Series Fusion Splicers

Model

Fujikura ADC-20

Product type

AC power adapter

Documented platform

Fujikura 90R fusion splicer

Power-cord configuration

Separate AC power cord; confirm the required plug and destination-market configuration before ordering

Fujikura BTR-15 Battery Pack for Select 90-Series Fusion Splicers

Model

Fujikura BTR-15

Product type

Rechargeable lithium-ion battery pack

Documented platform

Fujikura 90R fusion splicer

Manufacturer nominal output

Approximately 14.4 V DC

Manufacturer nominal capacity

6380 mAh

Manufacturer reference capacity

Approximately 165 splice-and-heat cycles under stated test conditions

Recharge temperature

0 °C to 40 °C

Long-term storage temperature

−20 °C to 30 °C

Battery-life reference

Capacity may decrease to approximately half after about 500 discharge/recharge cycles

Condition note

Actual capacity and cycle count depend on battery age, storage and operating conditions

Fujikura CB-08 Replacement Cleaver Blade for CT50

Model

Fujikura CB-08

Product type

Replacement fiber-cleaver blade

Documented compatible cleavers

Fujikura CT50, CT52 and CT58

Package contents

Confirm the supplied quantity before ordering

Fujikura FH-70-250 250 µm Coated Fiber Holders (Pair)

Model

Fujikura FH-70-250

Product type

Fiber-holder pair

Fiber configuration

250 µm coated single fiber

Documented platform

Fujikura 90R fusion splicer

Fujikura FH-70-900 900 µm Buffered Fiber Holders (Pair)

Model

Fujikura FH-70-900

Product type

Fiber-holder pair

Fiber configuration

900 µm jacketed single fiber

Documented platform

Fujikura 90R fusion splicer

古河Fitel S179A光纖熔接機

Alignment method

Active core alignment

Splice time (typical)

7 s

Heat time (typical)

18 s

Typical splice loss (SMF)

0.02 dB

古河電工 Fitel S326 光纖切割刀

Model

FITEL S327A (S327)

Fiber support

Single fiber and ribbon fiber

Ribbon capacity

Up to 12 fibers at 250 µm pitch; up to 16-fiber rollable ribbons at 200 µm pitch

Blade life

Up to 65,000 cleaves

Blade indexing

One-click blade rotation

Operation

Handheld or desktop; switchable lid opening angle

Komshine FX39 光纖熔接機

Alignment method

Active core alignment

Splice time (typical)

6 s

Heat time (typical)

15 s

Typical splice loss (SMF)

0.02 dB

VFL

Integrated, 10 mW class 3R

Orientek T45 光纖熔接機

Model

Orientek T45

Alignment method

Core alignment

Splicing time (manufacturer specification)

7 s

Heating time (manufacturer specification)

18 s

Display

4.3-inch touchscreen

Orientek T49 光纖熔接機

Alignment method

Active core alignment

Splice time (typical)

5 s

Heat time (typical)

13 s

Typical splice loss (SMF)

0.02 dB

Riselink 1-In/2-Out ABS Fiber Optic Splice Protection Box

Riselink 1.25/2.5 mm One-Click Fiber Optic Cleaning Pen and Box Tool Kit

Riselink 1.5–3.3 mm Loose Tube Slitter and Longitudinal Cutter

Riselink 10 mW / 10 km Visual Fault Locator Pen for Fiber Fault Tracing

Riselink 100-Piece Fiber Optic Cleaning Swab Set — 1.25/2.5 mm, LC/SC/FC/ST

Riselink 1000 m G.652D Single-Mode OTDR Launch Cable Box — Selectable Connector Ends

Fiber

G.652D single-mode.

Fiber length

1000 m.

Connector A

the selected OTDR-end connector.

Connector B

the selected link-end connector.

Housing

yellow protective case with Riselink branding.

Supply unit

one launch-cable assembly.

Specification

Use the selected variant name and SKU to identify the ordered connector pair.

Price: $131.00

Riselink 11-Piece Fiber Optic Cleaning Kit with 1.25/2.5 mm SC/FC/ST/LC One-Click Pens and Cleaning Box